Accessories

Logic Beach offers a full selection of accessories for our data acquisition and data logging instrument families.

IntelliLogger Specific Accessories

I/O Channel Expansion

ILIM-7 IntelliLogger Analog Input Expansion Module

ILIM-7 IntelliLogger Analog Input Channel Expansion Module

Isolated 8 channel analog input expansion module for the IntelliLogger™ system.

ILIM-2 Digital Input/Output Channel Expansion Module

ILIM-2 Digital Input/Output Channel Expansion Module

Event, Counter, Frequency Input and Digital Output channel expansion module for the IntelliLogger system.

BPB-1 BBus Power Booster

BPB-1 BBus Power Booster

Injects supply voltage in BBus network for applications with 5 or more Expansion Modules or long BBus cable runs.

Expansion module attached to the IntelliLogger base with angle attachment bracket

Expansion Module Attachment Bracket

Allows stacking of Expansion Modules and/or attachment to the IntelliLogger base.

CAT5 Standard Ethernet Cable, 10ft

Ethernet Cable

Various lengths of CAT5 Ethernet cable are available for use in building a BBus network.

BBus Termination Stub

Bbus Termination Stub

Install on last module to minimize reflected communication signal

Communications

LS300 Cellular Data Modem

Cellular Data Modems

Connection of a cellular modem facilitates M2M remote access to the IntelliLogger via the cellular data network.

12

12″ Magnetic Mount Omni Antenna

Antenna, magnetic mount, 12″ tall, omnidirectional whip with 10′ of RG174 (0.1″ dia) coax cable. 5dB dual-band for 850 and 1900MHz. Requires 5″ dia min ground plane.

Cellular Booster Amp Unit

Cellular Data Modem Booster Amp

Antenna, magnetic mount, 12″ tall, omnidirectional whip with 10′ of RG174 (0.1″ dia) coax cable. 5dB dual-band for 850 and 1900MHz. Requires 5″ dia min ground plane.

Short Range Wireless Ethernet Bridge

Short Range WiFi Bridge

With this Bridge, the IntelliLogger can be quickly deployed on a WiFi network. Unit is provided with 120Vac power supply and surface mounting cradle bracket.

CAT5 Standard Ethernet Cable, 10ft

Ethernet Cable

Various lengths of CAT5 Ethernet cable are available for use in building a BBus network.

Modbus Options

Modbus

Modbus Options Overview

Modbus RTU Master and Slave as well as Modbus TCP Server.

SCC-1 BBus Serial RS-232 to RS-485 Comm Converter

SCC-1 Serial Comm Converter

Converts IntelliLogger RS-232 port to RS-485 for Modbus RTU applications.

Power and Transducer Excitation

PSM-2 Sensor Excitation Power Supply Module

PSM-2 Sensor Excitation Power Supply

Step up power supply to provide cycled sensor excitation or 4-20mA loop power from batteries or nominal 12Vdc source.

120/240Vac 12Vdc Power Supply

120/240Vac 12Vdc Power Supply

Provides 12Vdc power for IntelliLogger operation.

120/240Vac 24Vdc Power Supply

120/240Vac 24Vdc Power Supply

Provides 24Vdc power for IntelliLogger operation. Additionally, applications using transducers (eg 4-20mA loop powered) that require nominal 24Vdc power can share this power supply for transducer power.

Stand-alone PSM-2 mounted in a small portable package with 6 D-cells

PSM-2-PP Sensor Excitation Power Supply

A stand-alone portable power supply including 6 D-Cell and the PSM in a small (4.8 x 8.8 x 2.9) package.

Protective Enclosures

IL-80 mounted in Enc250 with optional D-cell battery pack in door.

Enc250 Enclosure

Smallest size enclosure (10.5″W x 14″H x 6.5″D). Typically used for housing an IntelliLogger and optionally one additional ILIM-x Channel Expansion Module and/or Cellular Modem.

Enc250 Surface Mounting Bracket

Enc250 Wall/Surface Mounting Bracket

Wall/surface mounting bracket. Aluminum bracket mounts to the back of the Enc250 enclosure. Flanges project at the top and bottom of the enclosure with mounting holes for wall or other surface securement.

IL-80 mounted in Enc300 with one additional ILIM-7 Analog Input Module and Cellular Modem

Enc300 Enclosure

Medium size enclosure (11.7″W x 20.4″H x 7.1″D ). Typically used for housing an IntelliLogger and optionally up to 3 or 4 additional ILIM-x Channel Expansion Modules. Alternatively, a mix of modules and ancillary equipment (Cell Modem, Power Supplies, battery pack, etc) fits well into the Enc300.

Enc300 Surface Mounting Bracket

Enc300 Surface Mounting Bracket

Wall/surface mounting bracket. Aluminum bracket mounts to the back of the Enc300 enclosure. Flanges project at the top and bottom of the enclosure with mounting holes for wall or other surface securement.

Enc350 with two additional ILIM-7 modules, SCC-1, D-Batt pack and WiFi bridge.

Enc350 Enclosure

Largest enclosure (14.8″W x 25″H x 9.2″D ). Typically used for housing an IntelliLogger and optionally up to 5 additional ILIM-x Channel Expansion Modules or a mix of modules and/or ancillary data acquistion system components (cell modem, sensor power supplies, AGM batteries, charge controllers, etc).

Enc350 Surface Mounting Bracket

Enc350 Surface Mounting Bracket

Wall/surface mounting bracket. Aluminum bracket mounts to the back of the Enc350 enclosure. Flanges project at the top and bottom of the enclosure with mounting holes for wall or other surface securement.

Antenna Gland Fitting and nut shown with Antenna

Antenna Gland Fitting

Medium size sealing gland fitting fits 3/4″ diameter machined hole in the EncXXX enclosure. Fitting hole is sufficiently sized to pass TNC RF connector and yet compress to seal agains RG174 coax cable as provided on the Omni-Directional cellular antenna.

Gland fitting for Ethernet cable egress

Ethernet Gland Fitting

Use of this gland fitting allows for connetion of hardwired Ethernet cable to an IntelliLogger housed within an EncXxx enclosure. Large size sealing gland fitting fits 7/8″ diameter machined hole in the EncXxx enclosure. Fitting hole is sufficiently sized to pass standard RJ45 Ethernet connector plug and yet compress to seal tight to the Cat5/6 standard Ethernet cable jacket.

D-Cell Battery Pack shown mounted into EncXxx enclosure door

D-Cell Battery Pack

The optional D-Cell battery pack can be installed in an EncXXX enclosure door and used to power the IntelliLogger for true off-grid stand-alone operation.

Other IntelliLogger Accessories

Surface mounting plate. Bracket mounts to back of Data Logger and extends above and below.

Surface Mounting Bracket

For attaching IntelliLogger or Expansion Modules to a wall or enclosure back.

CF-IND-128K Compact Flash Memory Card

CF Memory  Card

Insert to enlarge data storage capacity as well as facilitate logged data transport.

IntelliLogger and LS300 Modem in optional tamper/weatherproof IL-250 enclosure

Enclosures

Weather and tamperproof protective enclosures.

Example Calibration Certificate for Data Logger

Calibration Certificate

An optional Certificate of Calibration can be provided with the instrument at time of order or up to 6 months after manufacture.

50mA Power Input Protection Fuses

50mA Power Input Protection Fuses

Fuses protect the analog inputs from over-current when configured as mAdc inputs. Replacement fuses are available in 5 packs.

3A Power Input Protection Fuses

3A Power Input Protection Fuses

Fuses protect the analog inputs from over-current when configured as mAdc inputs. Replacement fuses are available in 5 packs.

SureCross Node

SureCross Wireless Sensor Network Gateway

A suite of wireless sensor nodes that allow for remote sensing.

IL-Mini Accessories

IL-Mini™ With optional surface mounting bracket

Surface Mounting Bracket

Brushed aluminum bracket with screws for mounting the IL-Mini within a cabinet or flat surface.

CF-IND-128K Compact Flash Memory Card

CF Memory  Card

Insert to enlarge data storage capacity as well as facilitate logged data transport.

Icon based programming via HyperWare-II software

HyperWare-II IL-Mini Single User License

Use of HyperWare-II with the IL-Mini requires a User license.

120/240Vac 12Vdc Power Supply

120/240Vac 12Vdc Power Supply

Provides 12Vdc power for IntelliLogger operation.

120/240Vac 24Vdc Power Supply

120/240Vac 24Vdc Power Supply

Provides 24Vdc power for IntelliLogger operation. Additionally, applications using transducers (eg 4-20mA loop powered) that require nominal 24Vdc power can share this power supply for transducer power.

USB Cable Type-A to Mini-B

USB Cable Type-A to Mini-B

6ft Type-A to Mini-B cable for IL-Mini to PC USB port connection.